Know your Td5
How the engine works, what goes wrong with it, and how to put it right. Written by people who rebuild, modify and fit Td5s every week.

Find the problem on the engine
Tap a part of the engine to see what it does, the symptoms when it fails, and how we fix it.
Simplified diagram drawn for TotalTd5, viewed from above. Not to scale.
10P or 15P? Which Td5 have you got?
Some parts differ between early and late engines, so it matters when you order. The engine code is the start of the engine number, stamped on the left-hand side of the cylinder block below the exhaust manifold. Land Rover groups the prefixes 10P to 14P as the early engine and 15P to 19P as the Euro 3 engine. The changeover came in about 2002 and was not tied to the Discovery 2 facelift.
10P
Early engines, Euro 2
- Defender and Discovery 2, from launch in 1998 until about 2002
- Fuel pressure regulator with no external spill pipe
- EGR fed by a plain flexible pipe
15P and 16P
Late engines, Euro 3
- 15P in the Defender from 2002 to 2007, 16P in the Discovery 2 from 2002 to 2004
- Fuel pressure regulator with an external spill pipe
- Water-cooled EGR
Parts that changed with the Euro 3 engine include the injectors, cylinder head casting, fuel pressure regulator, EGR, radiator and intercooler, boost pressure sensor and air cleaner lid, engine wiring loom and ECU. If you're not sure which you have, send Dean your engine number when you order. How to check.
Td5 technical data
The numbers behind the engine, for when you're diagnosing, rebuilding or planning more power. Want more than standard? See the TD5Inside remap.
Engine
- Type
- 2.5 litre in-line 5 cylinder direct injection diesel, turbocharged and intercooled
- Bore x stroke
- 84.45 x 88.95 mm
- Capacity
- 2498 cc
- Firing order
- 1-2-4-5-3
- Compression ratio
- 19.5:1
- Max governed speed
- 4850 rpm
- Idle speed
- 740 rpm, +50
- Dimensions (L x W x H)
- 766 x 708 x 788 mm
Fuel and injection
- Injectors
- Lucas EV1 electronic unit injectors
- Injection pressure
- 1500 bar EU2 (10P to 14P), 1750 bar EU3 (15P to 19P)
- Fuel pump
- Electric two-stage, in the tank
- Regulated pressure
- 4 bar
- Filter
- In-line canister and water separator with water detection
- Glow plugs
- Beru 12 V, cylinders 1 to 4 only
Turbo and oil
- Turbo
- Garrett GT2052
- Oil pressure, cold idle
- 3.0 bar
- Oil pressure, hot at 3500 rpm
- 1.5 to 3.0 bar
- Relief valve opens
- 4.0 bar
- Oil filtration
- Centrifuge filter plus disposable full-flow canister
Cooling
- Thermostat
- Opens at 82°C, fully open at 96°C
- Expansion tank cap
- 1.4 bar
- Fans
- Viscous fan plus electric fan
- Electric fan
- On at 50 mph and below with ambient 28°C or above, off above 62 mph or below 25°C
Valves
- Valve head diameter
- Inlet 34.7 mm, exhaust 31.7 mm
- Seat angle
- Inlet 30°, exhaust 45°
- Valvetrain
- Hydraulic lash adjusters with followers, duplex chain driven camshaft
Technical data from TD5Inside. Always check against the workshop manual for your vehicle.
Common Td5 problems
Warped exhaust manifold
What you'll notice
- Whistling or chirping under boost
- Snapped or loose manifold studs
- Soot marks around the manifold flange
How we fix it
A de-webbed, heat treated and skimmed manifold with extended studs and stainless spacers, so it stays flat.
TotalTd5 manifold kit, £240Oil in the wiring

What you'll notice
- Misfire, often worse when hot
- Rough idle or cutting out
- Oil inside the ECU red plug
How we fix it
Oil wicks along the injector harness under the rocker cover. Cleaning the plug helps for a while; replacing the harness cures it.
Book it inCracked cylinder head
What you'll notice
- Coolant loss with no visible leak
- Overheating or pressurised coolant
- White smoke
How we fix it
A new AMC head, or our CNC ported head for more power, clamped with uprated head studs.
Cylinder heads and head studsFailing harmonic damper
What you'll notice
- Wobble on the crank pulley
- A squeak just as the engine stops
- A marble-like rattle at idle
- Belt noise or a thrown belt
- Rubber separating on the pulley
How we fix it
A Ross performance harmonic damper, with or without the bolt and fitting tool.
Ross harmonic damperOverheating
What you'll notice
- Temperature rising when towing or off-road
- Split plastic header tank
- Coolant loss
How we fix it
The Td5 doesn't tolerate heat well, so the cooling has to be right. Uprated alloy radiators and alloy header tanks.
Cooling partsDual mass flywheel judder
What you'll notice
- Judder pulling away in first
- Rattle at idle
- Clutch slip after a remap
How we fix it
LOF clutch and solid mass flywheel kits, specced to your power and how you use the vehicle.
Clutch and flywheel kitsLoss of power, cutting out under load
What you'll notice
- Power cuts out on long hills or hard acceleration
- Kangaroo surging as power comes and goes
- Fine again at light throttle
How we fix it
Often the wastegate modulator failing, so the turbo overboosts and the ECU cuts fuel to protect the engine. A diagnostic check confirms it, and the modulator is a cheap part.
Book a diagnosticCoolant dripping from the fuel cooler
What you'll notice
- Pink coolant dripping under the front of the engine
- Leaks when cold and parked, not when hot
- Wet front end of the fuel cooler on the inlet side
How we fix it
Usually a flattened O-ring on the cooler end cap, not the whole cooler. A new Viton O-ring stops it for a fraction of the price of a new unit.
Book it inOil leak at the front of the engine
What you'll notice
- Fresh oil on the front of the head and block
- Oil on the sump below
- The round camshaft seal at the front of the head moves when pushed
How we fix it
The push-fit front camshaft seal wears its O-ring flat. A new seal is a quick, cheap fix once the engine cover and fan cowl are off.
Book it inGearing calculator
Compare your Td5 as it is now with the set-up you're planning: bigger tyres, a different transfer box, new diffs or even a gearbox swap. See the revs in every gear, high and low range, side by side. Built on Ashcroft Transmissions' ratio data.
Ashcroft's own worked examples aim for about 2,700 rpm at 70 mph in top.
Gear, transfer box and diff ratios from Ashcroft Transmissions' ratio calculator, which TotalTd5 recommends for planning any gearing change. Figures are a guide. Planning a change? See LT230 transfer boxes and diffs, or ask Dean.
Td5 gearbox and transfer box guide
How to identify your R380, which LT230 ratio suits your tyres, what the upgrades actually do, and the oils and torque figures you need when the work's done.
Identify your R380
The serial number is stamped on a machined flat near the drain plug: a prefix, six digits and a suffix letter, for example 68A123456L. Suffix A to H is the older LT77. J onwards is an R380.
| Serial prefix | Fitted to |
|---|---|
| 67A or 73A | Td5 Discovery 2 |
| 68A or 74A | Td5 Defender |
| 56A or 58A | 300Tdi Defender |
| 55A | 300Tdi Discovery 1 and Range Rover Classic |
Every Td5 R380 is a long pinion box, suffix K or L, with its own input shaft and laygear (TUO100100). A 300Tdi box is not a straight swap.
What wears out
- Output shaft splines and the 5th and reverse splines
- The locking collar
- Gear face hardening on high mileage boxes, which looks cloudy and discoloured
- Dog teeth on first gear
Standard or heavy duty R380?
Both are rebuilt by Winchester Gears with new bearings, synchros and seals. The heavy duty R380 adds a machined rear housing for larger rear support bearings, and an upgraded oil feed ring that gets more oil to the mainshaft.
Worth it for towing, expedition travel, competition, or a tuned Td5 working hard.
Stage 1 and Stage 2 LT230
Only from Winchester Gears. Both have a double-sleeved casing (the intermediate shaft bore and the mainshaft bearing bore) and a hardened heavy duty intermediate shaft.
- Stage 1: heavy duty one-piece cross pin in the centre diff. For modified or hard-worked vehicles.
- Stage 2: ATB limited slip centre diff, for better traction between the axles. Off-road, towing and big power.
Both carry a 24 month warranty. Build your LT230
Which LT230 ratio?
A numerically higher ratio gives more pulling power and low-speed control, and brings back drivability on bigger tyres. A lower one drops your cruising revs. Try the numbers in our gearing calculator.
| Ratio | Origin | What it does |
|---|---|---|
| 1.667 | Land Rover | Lowest gearing. Towing, off-road, or getting drivability back on much bigger tyres. |
| 1.410 | Land Rover | The Td5 Defender standard ratio (43D and 57D boxes). On a Discovery 2, a popular change for 33 to 35 inch tyres. |
| 1.301 | Ashcroft | In between, for custom builds. |
| 1.211 | Land Rover | The Td5 Discovery 2 standard ratio. On a Defender, a taller option that drops cruising revs. |
| 1.1 | Ashcroft | Taller. Lower revs when cruising, for tuned engines. |
| 1.003 | Land Rover | Very tall, from the Range Rover P38 manual. Rare. |
| 0.9 | Ashcroft | Special applications only, such as Cummins and ZF auto swaps. |
LT230 upgrades explained
High capacity sump
The standard sump holds about 2.3 litres. A high capacity sump adds 0.5 to 1 litre, runs cooler and usually has a better magnetic drain plug. Bolt-on for every LT230.
300M output shaft
The standard output shaft is fine for a standard vehicle. On a tuned Td5, big tyres or heavy towing, a 300M shaft stops it twisting or shearing.
Output flange and propshafts
A genuine Land Rover double cardan front propshaft (Discovery 2 style) needs the double cardan output flange. Standard propshafts and Gwyn Lewis double cardan shafts use the standard flange. Get it wrong and you'll get vibration and worn joints.
Oils
| Unit | Oil | Capacity |
|---|---|---|
| R380 gearbox | MTF94 or Swepco 712 | 2.4 litres |
| LT230 transfer box | EP90 or Swepco 201, or 75W-90 Swepco 202 | 2.3 litres, plus 600 ml with a high capacity sump |
| Front and rear diffs | EP90 or Swepco 201, or 75W-90 Swepco 202 | 1.75 to 2.5 litres each |
| Anything with an ATB fitted | Mineral oil only: EP90 or Swepco 201 | As above |
LT230 torque settings
| LT230 fixing | Torque | Note |
|---|---|---|
| Drain plug | 30 Nm | |
| Output flange nuts | 162 Nm | Replace |
| Differential carrier bolts | 60 Nm | Thread lock |
| Differential bearing nut | 72 Nm | Replace |
| Transmission brake backplate bolts | 72 Nm | |
| Rear output housing bolts | 45 Nm | Thread lock |
| Front output housing bolts | 25 Nm | Thread lock |
| Bottom cover bolts | 25 Nm | Thread lock |
| Neutral warning lamp switch | 25 Nm |
Based on Winchester Gears' R380 information, standard or heavy duty R380, LT230 ratios, Stage 1 and 2 LT230, high capacity sump, output shaft, output flange and torque settings guides, and their oil guide. Always check against your workshop manual. Not sure what you need? Ask Dean.
Td5 Defender axle parts and part numbers
Rebuilding a Td5 axle, or chasing a clunk, weep or knock? Here are the parts and part numbers for the Defender front axle, the rear 90 and late 110 axle and the late Salisbury, with the heavy duty upgrades worth considering while it's apart. Quantities are per axle.
The parts that wear out first
DA3179GDA3180G on ABS axles. Weeping swivels and heavy steering are the signs.
RTC3429GSame bearing front and rear, 4 per axle. Play or rumble at speed means it is time.
FTC4785GChange them whenever the hubs come off. Oil on the brakes is the giveaway.
RUC105200GWorn splines clunk on and off the throttle. Ashcroft 859 is the heavy duty fix.
TDB500290 / TDB500280Clicking on full lock. Ashcroft HD for big tyres or a tuned engine.
561196 / NY606042GWorth replacing when a diff comes out, 10 of each per axle.
Full parts lists by axle
Front axleDefender 90, 110 and 130, post-1994: 300Tdi, Td5 and TDCi+
Swivels and steering
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Swivel kit | DA3179G | DA3180G with ABS | 2 |
| Swivel plug | 3292 | 2 | |
| Swivel bolts | UYG500050 | 14 | |
| Washer | FRC8530 | 10 | |
| Top swivel bolts | BX110071M | 4 | |
| Bottom swivel pin | FRC2894 | 2 | |
| Bottom swivel pin bolts | FS108307L | 4 | |
| Steering stop | TAU100170 | 2 | |
| Steering stop bolt | AFU1234 | 2 |
Hubs and bearings
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Stub axle kit | DA3192 | 2 | |
| Hub | RUB500240 | 2 | |
| Plate | FRC2310 | 2 | |
| Wheel bearing | RTC3429G | 4 | |
| Hub seal | FTC4785G | 2 | |
| Hub nut | FRC8700 | 4 | |
| Stub axle washer | FTC3185 | 2 | |
| Lock washer | FTC3179 | 2 | |
| Circlip | 549473 | 2 | |
| Disc bolt | LR082331G | 10 | |
| Hub cap | FTC5414LR | Not needed with HD flanges | 2 |
Driveshafts and flanges
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| CV joint | TDB500290 | Ashcroft HD | 1 |
| CV joint | TDB500280 | Ashcroft HD | 1 |
| Drive flange | RUC105200G | Ashcroft 859 HD | 2 |
| Shims | FRC6782 | 2 | |
| Drive flange bolt | RYG101010L | BX110095M | 10 |
| M10 spring washers | WL110001L | 14 |
Casing, diff and fittings
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Diff stud | 561196 | 10 | |
| Diff nuts | NY606042G | 10 | |
| Filler plug | 608246 | 1 | |
| Drain plug | TYB500120 | 1 | |
| Breather | FTC5085 | 1 | |
| Disc shield bracket | FRC3725 | 2 | |
| Disc guard | FTC4838 | 1 | |
| Disc guard | FTC4839 | 1 | |
| M6 x 12 bolts | FS106125L | 14 | |
| M6 nuts | NH106045 / NH106041L | 2 | |
| Brake pipe bracket, stainless | SHU000040SS | 1 | |
| Brake pipe bracket, stainless | SHU000050SS | 1 | |
| Sealant | Würth | 1 |
Brakes
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Brake discs | LR017952 (OE brand) | LOF brake kit | 1 |
| Caliper | SEB500460G | LOF brake kit | 1 |
| Caliper | SEB500470G | LOF brake kit | 1 |
| Brake pads | SFP000260F (OE brand) | LOF brake kit | 1 |
| Accessory kit | STC8575 | 1 | |
| Caliper bolts | SYP500090 | 4 |
Rear axle, 90 and late Rover-type 110Defender 300Tdi, Td5 and TDCi+
Hubs and bearings
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Stub axle kit | FTC3188K | 2 | |
| Hub | RUB500240 | 2 | |
| Mud shield | FRC2310 | 2 | |
| Wheel bearing | RTC3429G | 4 | |
| Hub seal | FTC4785G | 2 | |
| Hub nut | FRC8700 | 4 | |
| Stub axle washer | FTC3185 | 2 | |
| Lock washer | FTC3179 | 2 | |
| Disc bolts | LR082331G | 10 |
Half shafts and flanges
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Half shaft, long | TOB500030 | Ashcroft HD late fixed shaft LRO72976 | 1 |
| Half shaft, short | TOB500020 | Ashcroft HD late fixed shaft LRO72977 | 1 |
| Drive flange | RUC105200G | Ashcroft HD 859 | 2 |
| Drive flange bolts | RYG101010L | BX110095M | 10 |
| Circlip | 549473 | Not needed with one-piece shafts | 2 |
Casing, diff and fittings
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Differential nylocks | NY606042G | 10 | |
| Differential studs | 561196 | 10 | |
| Filler plug | 608246 | 1 | |
| Drain plug | TYB500120 | 1 | |
| Breather | FTC5085 | 1 | |
| Disc guard bracket | LR017513 | 2 | |
| M6 bolts | FS106125L | 6 | |
| Washer | 2215L | 2 | |
| Disc guard | LR017960 | 1 | |
| Disc guard | LR017961 | 1 | |
| ABS bush | LR029522 | Only on an ABS axle | 2 |
| Sealant | Würth | 1 |
Brakes
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Brake discs | LR018026AP (OE brand) | LOF brake kit | 1 |
| Caliper | SMC500260G | LOF brake kit | 1 |
| Caliper | SMC500270G | LOF brake kit | 1 |
| Brake pads | SFP000250 (OE brand) | LOF brake kit | 1 |
| Accessory kit | BA1994 kit (comes with Ferodo pads) | 1 | |
| Caliper bolt | SYP500090 | 4 |
Rear axle, late Salisbury 110Defender 110 and 130 Td5+
Hubs and bearings
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Stub axle kit | FTC3188K | 2 | |
| Hub | RUB500240 | 2 | |
| Mud shield | FRC2310 | 2 | |
| Wheel bearing | RTC3429G | 4 | |
| Hub seal | FTC4785G | 2 | |
| Hub nut | FRC8700 | 4 | |
| Stub axle washer | FTC3185 | 2 | |
| Lock washer | FTC3179 | 2 | |
| Disc bolts | LR082331G | 10 |
Half shafts and flanges
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Half shaft, long | FTC1725 | Ashcroft HD late Salisbury | 1 |
| Half shaft, short | FTC1724 | Ashcroft HD late Salisbury | 1 |
| Drive flange | RUC105200G | Ashcroft HD 859 | 2 |
| Drive flange bolts | RYG101010L | BX110095M | 10 |
| Circlip | 549473 | 2 |
Casing and fittings
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Filler plug | 608246 | 1 | |
| Drain plug | TYB500120 | 1 | |
| Breather | FTC5085 | 1 | |
| Disc guard bracket | LR017513 | 2 | |
| M6 bolts | FS106125L | 6 | |
| Washer | 2215L | 2 | |
| Disc guard | LR017960 | 1 | |
| Disc guard | LR017961 | 1 | |
| ABS bush | LR029522 | Only on an ABS axle | 2 |
| Sealant | Würth | 1 | |
| Fulcrum mount bolts | AEU2508 | Optional | 4 |
| Diff pan and M10 x 25 bolts (10) | RTC844 | Optional | 1 |
Brakes
| Part | Part number | Upgrade or note | Qty |
|---|---|---|---|
| Brake discs | LR018026AP (OE brand) | LOF brake kit | 1 |
| Caliper | SMC500260G | LOF brake kit | 1 |
| Caliper | SMC500270G | LOF brake kit | 1 |
| Brake pads | SFP000250 (OE brand) | LOF brake kit | 1 |
| Accessory kit | BA1994 kit (comes with Ferodo pads) | 1 | |
| Caliper bolt | SYP500090 | 4 |
Part numbers from the Winchester Gears Defender axle parts list, with thanks to Winchester Gears. Always check against your VIN and axle before ordering, as Land Rover changed parts during production. Brake upgrades: see our LOF and AP Racing brake kits.
Need the parts, or the whole axle? We can supply genuine, OE or heavy duty parts, rebuild your axle, or supply a complete Winchester Gears axle built to your spec.
Choosing a diff centre for your Td5
The centre is the heart of each differential: the spider gears in a standard diff, or a limited slip or locking mechanism in an upgraded one. Get it right and you add strength for torque and big tyres, traction off-road, and control of wheelspin without spoiling how the vehicle drives on the road.
The options
Factory centre with 2 pin spider gears.
A standard or lightly modified Td5 on standard size tyres. The 2 pin centre is a known weak point, especially in the rear diff.
Four spider gears share the load instead of two. Far stronger than standard.
Our baseline for any tuned Td5, an auto, or tyres bigger than 32 inches. Essential off-road with big tyres.
Helical limited slip diff. Shifts drive to the wheel with grip, automatically. UK made.
Fast road, daily and overland. More traction with no switches, no compressor and no change to how it drives on the road.
Helical limited slip diff, US made. Very strong, with a slightly firmer feel under load.
The same jobs as the Ashcroft ATB. Good for heavy builds or if you prefer the Detroit brand.
Locks fully at the flick of a switch. Needs a compressor and wiring.
Serious off-road, rock and mud. Drives like an open diff on the road, 100% locked when you need it.
Selectable air locker from the best known name, with excellent support.
Extreme off-road and expedition builds where the ARB brand matters. Costs a little more.
What we'd fit for your build
| Your build | Suggested centres |
|---|---|
| Standard Td5, standard tyres | Standard centre, or an ATB for safer traction |
| Tuned daily driver, standard size tyres | 4 pin HD centre, or ATB |
| Tuned Td5 or engine swap on 32 to 33 inch tyres | 4 pin HD centre, plus ATB or lockers |
| Off-road biased on 33 to 35 inch tyres | 4 pin HD centre, plus air lockers front, rear or both |
| Competition on 37 inch tyres and up | 4 pin HD centre, plus air lockers front and rear |
| Overland Defender 110 or 130 | 4 pin HD centre, plus ATB or air lockers front and rear |
ATB or air locker?
ATB: fit and forget. It works on its own, no switches or compressor, and it's at its best on the road and in snow and ice.
Air locker: the one for deep mud, rocks and competition. Full lock when you switch it on, open diff when you don't, but you'll need an air supply and wiring.
The short version
If your Td5 is tuned or on bigger tyres, start with a 4 pin heavy duty centre in each diff. Then add an ATB or air lockers depending on how much traction you need. Pegged diff casings are worth having on a tuned Td5 too.
Based on the Winchester Gears centre diff guide, with thanks to Winchester Gears.
Diff ratios, pegged casings and axle casings
Bigger tyres make a Td5 feel flat and lazy, and they work the gearbox and clutch harder. A lower diff ratio (a bigger number) brings the drivability back. Front and rear diffs must always have the same ratio.
Long nose diffs
All Defender and Discovery 2 front diffs, Defender 90 and Discovery 2 rear diffs.
| Ratio | Type | Best for |
|---|---|---|
| 3.54 | Standard | A standard Td5 on factory size tyres, such as 235/85 R16. Balanced for road and light off-road. |
| 3.5 | HD Ashcroft or GBR | A tuned Td5 on tyres up to about 32 inches. Keeps the factory feel and adds strength. |
| 3.75 | HD Ashcroft | 32 to 33 inch tyres. A little lower for better drivability without over-revving. |
| 4.12 or 4.1 | HD Ashcroft or HD GBR | 33 to 35 inch tyres or a heavily loaded vehicle, such as a 130 or an overland Discovery 2. |
| 4.37 | HD Ashcroft | Hardcore off-road and rock crawling on 35 to 37 inch tyres. Excellent low-speed control. |
| 4.75 | HD Ashcroft | Competition builds on 37 inch tyres and up, where you need maximum crawl ratio. |
Short nose diffs
Rear diff on the Defender 110 and 130 from 2002.
| Ratio | Type | Best for |
|---|---|---|
| 3.54 | Standard | A standard Td5 on factory size tyres. |
| 3.5 | HD GBR | A tuned Td5 on tyres up to about 32 inches. |
| 4.1 | HD Ashcroft | 33 to 35 inch tyres, heavier overland builds and high torque. Restores drivability on bigger tyres. |
Td5 examples
- Standard Td5 on factory tyres: 3.54 standard.
- Tuned Td5 on 32 inch tyres: 3.5 HD.
- Td5 Defender 110 on 35s, overland spec: 4.12 HD Ashcroft front, 4.1 HD Ashcroft rear.
- Competition truck on 37s: 4.75 HD Ashcroft.
Check what a ratio does to your revs in our gearing calculator, then build your diff.
Pegged diff casings
Under big torque the standard casing flexes and lets the crownwheel move away from the pinion. That chips teeth, kills bearings and can end in a broken diff. A pegged casing has a precision-fitted steel peg that stops the crownwheel moving, so the gears stay in mesh.
Worth having with:
- Tyres of 32 inches and up
- Lockers or ATBs
- A tuned Td5 or an engine swap
- Competition and rock crawling
- Heavily loaded overland trucks
Pegging is an option on every Winchester Gears diff we sell.
Axle casings: Land Rover or Maer
Land Rover OEM casings are new or refurbished genuine casings. The right choice for a standard-looking Defender or a restoration, with factory fit for brackets, mounts and brakes.
Maer casings are heavy duty aftermarket casings with thicker walls, stronger welds and better corrosion resistance. Choose them for bigger tyres, more power, heavy towing or hard off-road use.
Both are available on Winchester Gears axles. Ask Dean which suits your build.
Based on Winchester Gears' guides to long nose and short nose diff ratios, pegged casings and axle casings. TotalTd5 supplies Winchester Gears units: order through us and your gearbox, transfer box, diff or axle is built by Winchester Gears.
Guides and workshop diagrams
Step-by-step guides with diagrams. Free to read, whether you buy from us or not.
Fitting the TotalTd5 manifold kit
Removing snapped studs, stud and spacer order, tightening order and torque figures.
Diagnosis guideChecking the red plug for oil
Where the plug is, what oil contamination looks like and what to do about it.
Identification guideFinding your engine code
Where to find the engine number, quick checks under the bonnet, and which parts change.
Workshop diagramHead stud layout and sequence
Fitting the Total Td5 uprated head studs, with the tightening order drawn out.
Coming soon. Ask Dean in the meantime ExplainerWhat a remap really does
Why a map is built to your parts and use, and what has to be right before you add power.
Coming soon. Ask Dean in the meantime Workshop diagramTd5 cooling system layout
Radiator, header tank, thermostat and hoses, and where airlocks form after a refill.
Workshop guides
The jobs that come up most on a Td5, with Land Rover's torque figures. Tap a job to open it. Engine guides cover every Td5; the chassis guides are split by vehicle.
Engine and fuel
Oil pump sprocket boltEngine, all Td5. Half a dayFuel pressure regulatorEngine, all Td5. About an hourInjector seals and washersEngine, all Td5. A dayWater pump (coolant pump)Engine, all Td5. Half a dayIntercooler cleanEngine, all Td5. Half a dayViscous fan pulley bearingEngine, all Td5. Half a dayIn-tank fuel pumpFuel system, Discovery 2 and Defender. Half a dayClutch
Choosing a Td5 clutchDefender and Discovery 2 Td5. Gearbox outLT230 transfer box
LT230 transfer box oil changeTransfer box, Defender and Discovery 2. Under an hourLT230 output shaft oil sealsTransfer box, Defender and Discovery 2. Two hours per sealDefender: brakes, driveline and suspension
Defender front brake padsDefender chassis. About an hourDefender front discs and hubDefender chassis. Half a day per sideDefender front shock absorbers and bushesDefender suspension. Two hoursDefender propshaftsDefender driveline. Half a day per shaftDiscovery 2: brakes, driveline and suspension
Front discs and padsDiscovery 2 chassis. Two to three hoursPropshaft universal jointsDiscovery 2 driveline. Half a day per shaftFront shock absorber lower bushesDiscovery 2 suspension. Two to three hoursDownloads
- Land Rover Discovery 2 accessories brochure PDF, 3.2MB
Torque figures and limits from the Land Rover Discovery 2 workshop manual (VDR 100090) the Defender 1999 and 2002MY workshop manual supplement the Defender 2007MY workshop manual and the LT230T transfer box overhaul manual. Always check them against the manual for your vehicle.
Diagrams on this page are drawn for TotalTd5. We don't reproduce Land Rover workshop manual pages. Always check torque figures and procedures against your manual, and if you're unsure, ask us or book it in.